10/20/2026
How to Evaluate Hydrophilic Fumed Silica 200 by Its Technical Data

Introduction
“Hydrophilic Fumed Silica 200” usually signals a hydrophilic pyrogenic silica grade associated with a nominal BET surface area near 200 m²/g. The number alone is not a complete specification. Product ranges, test methods, pH conditions, moisture limits, bulk behavior and application treatment can vary by manufacturer. This guide shows how to read a technical data sheet and match the material to a formulation. Published values from Evonik and WACKER are included as examples of established reference grades; they are not specifications for Lemeng’s product and should not be transferred to another supplier without confirmation.
1. What the grade designation does and does not tell you
Fumed silica is a synthetic amorphous silicon dioxide produced by flame hydrolysis. Hydrophilic grades have surface silanol groups that interact with polar media and formulation components. A “200” family name commonly refers to a nominal specific surface area around 200 m²/g, but the supplier’s test method and specification determine the actual acceptance range. Evonik describes AEROSIL 200 as a hydrophilic fumed silica with a specific surface area of 200 m²/g and publishes a BET range of 175–225 m²/g. [1]
BET is only one property. pH depends on the specified dispersion; loss on drying affects handling and weighing. Tamped density informs volume feeding but is not true particle density. Compare methods and conditions, not just grade names.
2. Read the data sheet with the test conditions
Evonik’s AEROSIL 200 information reports BET surface area of 175–225 m²/g, pH of 3.7–4.5 in a 4% dispersion, loss on drying no more than 1.5% after two hours at 105°C, tamped density about 50 g/L and SiO₂ content above 99.8% based on ignited material. Evonik explicitly labels these as typical values rather than product specifications. WACKER’s HDK N20 lists BET of 175–225 m²/g, pH 3.8–4.3, tamped density about 40 g/L and loss on drying below 1.5%. These ranges provide a useful same-class comparison, not an endorsement or equivalence statement. [1][2]
For procurement, distinguish guaranteed limits from typical values. Request the current TDS and SDS for the exact grade; confirm BET and moisture methods, pH dispersion concentration and reporting basis. Do not turn a typical value into a contractual limit without supplier agreement.
Published reference-grade data
Reference product | BET surface area | pH condition/value | Other published values |
Evonik AEROSIL 200 | 175–225 m²/g | 3.7–4.5, 4% dispersion | LOD ≤1.5%; tamped density approx. 50 g/L |
WACKER HDK N20 | 175–225 m²/g | 3.8–4.3 | LOD <1.5%; tamped density approx. 40 g/L |
Manufacturer reference values only. Both manufacturers caution that data are guidance/typical for their named grades. These are not Lemeng specifications.
3. Connect powder properties to formulation behavior
High surface area fumed silica can build a three-dimensional particle network in liquid systems. Depending on formulation and dispersion, that network may increase low-shear viscosity, create thixotropic recovery, reduce settling or improve anti-sag behavior. Evonik lists rheology and thixotropy control, anti-settling, thickening and anti-sagging among AEROSIL 200 properties. WACKER describes HDK N20 as a thickening and thixotropic agent in organic systems and a free-flow additive for technical powders. Application behavior still depends on resin, solvent, pigment, temperature and dispersion energy. [1][2]
In coatings, rheology modification may reduce settling or sag; in adhesives and sealants it may support non-sag behavior under rest and flow under shear. Powder flow depends on base powder, humidity, mixing and dose. These are goals to verify in the actual formulation, not guaranteed outcomes.
4. Evaluate the grade with a controlled trial
Use a representative base and hold other ingredients and steps constant. Record addition basis, equipment, sequence, mixing time, speed and temperature. Measure viscosity, recovery, sag or settling, appearance and storage stability. For powders, control the chosen flow test and humidity; visual comparison alone is insufficient.
Because high-surface-area powder can be difficult to wet out, addition rate and shear history matter. Avoid dumping a full bag into a small vortex where airborne dust or agglomerates can form. The target is a reproducible dispersion without overprocessing the system. Record the actual energy or equipment settings where possible. If a disperser, rotor-stator or bead mill is used, verify that it is compatible with the formulation and does not introduce contamination or excessive heat.
5. Purchase and storage controls
On receipt, check the product name, batch number, packaging integrity, certificate and stated test values. Compare the certificate against the agreed limits and sampling plan. Retain a sealed reference sample if the quality agreement requires it. Do not reject a lot solely because a typical value differs slightly from a target that was never made contractual; instead follow the agreed specification and change-control procedure.
High surface area can make silica adsorb moisture and volatiles. Evonik recommends dry, closed storage and gives AEROSIL 200 a two-year use period. This is brand-specific, not Lemeng shelf life. Follow the purchased grade’s label and SDS. [1]
Handle fine powder with engineering controls appropriate to the task, such as closed transfer, local exhaust ventilation and minimizing drop height. Use the PPE and exposure controls in the product SDS and local rules. NIOSH’s Pocket Guide lists a REL of 6 mg/m³ TWA for amorphous silica; this is a U.S. occupational recommendation for the broad substance category, not a universal regulatory limit or a substitute for a workplace exposure assessment. [3]
6. What to ask a Hydrophilic Fumed Silica 200 supplier
Request exact grade, BET range and method, pH condition, loss-on-drying method, tamped density, SiO₂ basis, relevant sieve data, packaging, shelf life and SDS. Confirm hydrophilic versus surface-modified hydrophobic treatment; similar BET does not imply similar behavior.
For regulated uses, verify market-specific status, purity, traceability and change documentation for the exact grade. A generic fumed silica data sheet does not establish compliance.
FAQ
Does “200” guarantee exactly 200 m²/g? No. It is commonly a nominal grade designation; the published specification may allow a range such as 175–225 m²/g.
Can two grades with the same BET range be substituted directly? Not automatically. Surface chemistry, aggregation, pH, density and dispersion behavior can differ.
Is the listed pH measured on dry powder? No. It is typically measured in a specified aqueous dispersion; read the test condition.
Can a typical data-sheet value be used as an incoming acceptance limit? Only when the supplier has agreed that it is a guaranteed specification and the test method is defined.
Conclusion
Evaluate Hydrophilic Fumed Silica 200 beyond its grade name. Compare BET, pH, moisture, density and test methods, then confirm performance through a trial. The exact Lemeng specification must come from its current TDS and certificate.
